Poulan-pro PP208EPS24L Bedienungsanleitung

OWNER'S MANUALMODEL NUMBER:PP208EPS24LSNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read th

10TO CONTROL SNOW DISCHARGE (See Fig. 13)WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma-

11OPERATIONUSING THE CLEAN-OUT TOOL (See Fig. 15)In certain snow conditions, the discharge chute may be-come clogged with ice and snow. Use the clean-

12BEFORE STARTING THE ENGINECHECK ENGINE OIL LEVEL (See Fig. 19)The engine on your snow thrower has been shipped from the factory already filled with

13OPERATIONSNOW THROWING TIPS• Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the ON / OFF switch, to adjust speed.•

14 SAE 5W-30 Motor Oil See “ENGINE” inMaintenance section General Purpose GreaseGENERAL REC OM MEN DA TIONSThe warranty on this snow thrower d

15MAINTENANCEAUGER GEAR CASE• The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention

16SERVICE AND ADJUSTMENTSBELT COVER SCREWSFRAMEFIG. 21TO REMOVE BELT COVER (See Fig. 21)1. Remove the two (2) screws securing belt cover to frame.2.

17SERVICE AND ADJUSTMENTS8. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.HINT: Insert a 3/8"

18SERVICE AND ADJUSTMENTSENGINESee engine manual.CARBURETORYour carburetor is not adjustable. Engine performance should not be affected at altitudes u

19STORAGEImmediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never store t

2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure

20TROUBLESHOOTINGDoes not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2.

21REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

22REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

23REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

24REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

25REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches.

26REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches.

27REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPOR

28REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPOR

29REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPOR

3CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u -fac tured to give best possible dependability an

30REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPOR

31REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA

32REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA

33REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA

34REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)CHASSIS / ENGINE / PULLEYSNOTE: All component dimensions given in U.S. inches. 1

35REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)CHASSIS / ENGINE / PULLEYSNOTE: All component dimensions given in U.S. inches. 1

36NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement

37REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)WHEELSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORT

38REPAIR PARTS SNOW THROWER - MODEL PP208EPS24L (96198003801)BAG OF PARTSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

39NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement

4PARTS PACKED SEPARATELY IN CARTON(3) RETAINER SPRINGS (169675)(1) WASHER 3/8(19131316)(1) LOCKNUT 3/8(73800600) SAFTEY IGNITION KEY(S)(422663)(1) MU

LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi-als and

5Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual w

6ASSEMBLY / PRE-OPERATIONINSTALL TRACTION DRIVE CONTROL ROD(See Figs. 3 and 4)The traction drive control rod is installed on the snow thrower.1. Remo

7ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)NOTE: The multi-wrench provided in your parts bag may be used to ins

8OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with

9OPERATIONDrive speed control lever - used to select forward or reverse motion and speed of snow thrower.Traction drive control lever - used to engage