OWNER'S MANUALMODEL NUMBER:PP521ESSNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the Ow
10Figure 16 1. Rub Area 2. Wear Areas 12Stopping the EngineTo stop the engine, pull key out (Figure 17).Figure 171. Key1Adjusting the Discharge
11Clearing a CloggedDischarge ChutePreventing Freeze-up afterUse• Let the engine run for a few minutes to prevent moving parts from freezing. Stop th
12MaintenanceNOTE: Determine the left and right sides of the machine from the normal operating position.Check for Loose FastenersClean / Inspect Snow
13Adjusting the Control CableChecking the Control CableRelease the control bar to remove the slack in the control cable (Figure 20).IMPORTANT: The con
14Changing the Engine OilRun the engine a few minutes before changing the oil to warm it. Warm oil flows better and carries more contaminants.4. Pla
15Servicing the Spark PlugUse a NGK BPR6ES, Champion RN9YC, or BOSCH WR6DC spark plug or equivalent.1. Stop the engine and wait for all moving parts
16Replacing the Drive BeltIf drive belt becomes worn, oil-soaked, excessively cracked, frayed, or otherwise damaged, replace the belt.1. Remove the
17StorageStoring the SnowthrowerImmediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days
18TroubleshootingSee appropriate section in manual unless directed to an authorized service center/department.PROBLEM CAUSE CORRECTIONDoes not start 1
19SERVICE NOTES
2Safe Operation Practices for Walk-Behind Snow ThrowersIMPORTANT: This snow thrower is capable of amputating hands and feet and throwing objects. Fai
20REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP521ES (96188000600)CHUTE ASSEMBLYNOTE: All component dimensions given in U.S. inches. 1 inch = 25
21REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP521ES (96188000600)CHUTE ASSEMBLYNOTE: All component dimensions given in U.S. inches. 1 inch = 25
22KEY PART NO. NO. QTY DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NUMBER PP521ES (96188000600)HANDLE ASSEMBLY1234556SSST-Handle asm
23REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP521ES (96188000600)AUGER ASSEMBLY9910101234567781111111212131345561114SSST-Auger asm_1NOTE: All comp
24REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP521ES (96188000600)SHROUD ASSEMBLY14315161616111221089101061515714517SSST-Shroud asm_14181920192021NO
25REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP521ES (96188000600)SHROUD ASSEMBLYNOTE: All component dimensions given in U.S. inches. 1 inch = 2
26REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP521ES (96188000600)FRAME ASSEMBLYNOTE: All component dimensions given in U.S. inches. 1 inch = 25
27REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP521ES (96188000600)FRAME ASSEMBLYNOTE: All component dimensions given in U.S. inches. 1 inch = 25
28REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP521ES (96188000600)DRIVE ASSEMBLY91234568711121312SSST-Drive asm_6NOTE: All component dimensions giv
29SERVICE NOTES
3CUSTOMER RESPONSIBILITIES• Read and observe the safety rules.• Follow a regular schedule in maintaining, caring for and using your snow thrower.•
30REPAIR PARTSSNOW THROWER - - MODEL NUMBER PP521ES (6188000600)ENGINE, LCT COMPLETE ENGINE-4359452626
31REPAIR PARTSSNOW THROWER - - MODEL NUMBER PP521ES (6188000600)ENGINE, LCT COMPLETE ENGINE-435945KEY
32LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in mate-rials an
4KNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Com-pare the illustrations with your sn
5SetupLoose PartsUse the chart below to verify that all parts have been shipped. Procedure Description Qty. Use 1. No parts required – Unfold the ha
6Product OverviewFigure 61. Discharge chute2. Chute deflector handle3. Fuel tank cap4. Control bar5. Recoil start handle6. Primer7. Chok
7OperationNOTE: Determine the left and right sides of the machine from the normal operating position.• Gasoline is extremely flammable and explosive.
8Starting the Engine1. Push key in (Figure 9).2. Move choke lever to left position (Figure 10).3. Firmly push in the primer 2 times with your th
9Engaging the Auger BladesTo engage the auger blades, hold the control bar against the handle (Figure 14).Disengaging the AugerBladesTo disengage the
Kommentare zu diesen Handbüchern